Brand: Panasonic
Model: TC 1612R
Symptom: No sound is totally dead ddesis
Cause: voltage 24v short
Solution: replace the vertical ic AN 5521
Devices: TV
Brand: Panasonic
Model: TC 2110BC
Symptoms: black picture, normal sound
Cause: elco 220u / 160v dry / leaky
Solution: replace elco 220u / 160v
Devices: TV
Brand: Panasonic
Model: forgot boss
Symptoms: total dead, voice berdenyit2
Cause: short zener56v
Solution: replace the zener and the issue is resolved
Note: liver chasise nyetrum
Devices: TV
Brand: Panasonic
Model: TC.21RY21J
Symptoms: 1.sinyal weak picture is similar symptoms agc.2. FRAME gambar damage rather narrow top and bottom
Cause: ic 851 5v output decreases TEG
Solution: replace R889 3.3ohm
Devices: TV
Brand: Panasonic
Model: Goldseris
Symptoms: Tv tidakbisa start voltage had risen high
Cause: Elko 47uf / 50v the series SMPS dry replace both ways
Solution: Check the voltage B + and zener second check Elko 47uf / 50v on the primary SMPS also check elko the secondary part SMPS
Note: Check the circuit bost up
Devices: TV
Brand: Panasonic
Model: TC21FJ50J
Symptoms: Arise Horizontal lines
Cause: Cracks on the vertical IC
Solution: re-solder the vertical section and replace capacitor bag. vertical
Devices: TV
Brand: Panasonic
Model: tc-2012Rc
Symptoms: can not keep a program canel.
Cause: one diode OA90ag there are broken / short.
Solution: check of diode 5 is one of some end / short.tipe is difficult in can store disposable .ganti wrote former old school radio, but I try to replace the use in 4148 could be.
Devices: TV
Brand: Panasonic
Model: mx series
Symptoms: Protec, must press the power button over and over new start
Cause: Elko 10 / 35v rather short
Solution: replace elco 10 / 35v ato 100 / 35v
Devices: TV
Brand: Panasonic
Model: tc2088
Symptoms: Contrast can not be set
Cause: ABL 220k resistor weak / change resistance
Solution: replace the R 220K ABL
Devices: TV
Brand: Panasonic
Model: TC1450
Symptoms: NO NO SOUND
Cause: Muting INPUT
Solution: CHECK / CHANGE Q1112 and Q 1113
Devices: TV
Brand: Panasonic
Model: TC1450
Symptoms: blangking & Protek
Cause: QUT NO NO VIDEO
Solution: CHANGE IC AN5600
Devices: TV
Brand: Panasonic
Model: TC20T8
Symptoms: TOTAL OFF
Cause: REGULATOR NOT WORK
Solution: CHANGE AND Q804 Q801 C4804 / A1215
Devices: TV
Brand: Panasonic
Model: t20m88
Symptoms: plain raster, blawur, OSD nothing but inarticulate, ill fokus.suara there.
Causes: Abnormal focus voltage
Solution: kmbali trimpot sets the focus FBT, loose and check CRT socket, measure the resistance gnd pin CRT thd other pin, position x10k ohm meter, if the needle moves sdikit course, you should replace the socket.
Devices: TV
Brand: Panasonic
Model: 21 Inch
Symptoms: The first turned on Image Blur (morbidly Focus) .After +/- 5 minutes, the picture gradually to normal
Cause: Socket tube corrosion (Gross)
Solution: Replace the Tube Socket
Devices: TV
Brand: Panasonic
Model: mc691wj
Symptoms: dim and bright images alternately
Cause: rgb ground problematic
Solution: re-solder ground wires
Devices: TV
Brand: Panasonic
Model: TC14V11
Symptoms: B + high so 110V, 90V normal, working Protek
Cause: R832 (5K6) burning, R837 (1K) broke
Solution: Replace R832 and R837
Devices: TV
Brand: Panasonic
Model: st1465
Symptoms: sounds shrink
Cause: IC 2145 damaged
Solution: replace the IC 2145
Devices: TV
Brand: Panasonic
Model: tc2076rs
Symptoms: total dead, there is a hissing sound, flyback leak
Cause: hit by lightning, flyback leaking and damaged
Solution: replace the flyback
Devices: TV
Brand: Panasonic
Model: gold alfa series
Symptoms: total dead, LED indicators die
Cause: damage to the power supply
Solution: check elco2, 7805 at the regulator ic
Devices: TV
Brand: Panasonic
Model: TC 14S10J
Symptoms: white screen and white blangking lines
Cause: The resistor R 374 1ohm / 2watt breaking result of IC TDA 6107JF short
Solution: replace the R 374 and ic 6107JF to the new TDA
Devices: TV
Brand: Panasonic
Model: tc 2088
Symptom: hoarse voice
Cause: 2301 diode short
Solution: replace the D2301
Devices: TV
Brand: Panasonic
Model: 2088 21 INCH
Symptom: POWER ON OFF AGAIN
Cause: RANKAIN PROTEKTOR BROKEN
Solution: CHECK / CHANGE TR Q451 (A564) Series of ICs AN5607NK PIN TO 20
Devices: TV
Brand: Panasonic
Model: jadul
Symptom: No sound mencuit total dead in the transformer swiching
Cause: faulty diode voltage divider ..
Solution: replace the diode RM 25 or with 56 V zener diode equation ....
Devices: TV
Brand: Panasonic
Model: TC-2088MNB
Symptoms: Led indicator blinking
Cause: D511 (sensor heater) experienced short
Solution: replace part dg new diode
Note: SUCCESS FOR ALL PARTNERS-ASSOCIATES
Devices: TV
Brand: Panasonic
Model: TC 2088
Symptom: The image is dark, no sound.
Cause: At the ABL.
Solution: Check the R525- 150 Kohm.
Devices: TV
Brand: Panasonic
Model: yg-made transformer C1C6A
Symptoms: cut no picture and sound
Cause: Panasonic diode short, Elko Regltr 47uf / 35v & 47uf / 50v
Solution: replace all existing in the cause.
Devices: TV
Brand: Panasonic
Model: quintrik
Symptoms: raster blawur colorful
Cause: corrosion tube socket
Solution: replace the socket tube, with a new guaranteed
Devices: TV
Brand: Panasonic
Model: blek series
Symptoms: Buyi live cit cit ga
Cause: short-circuit zener diode
Solution: replace the zener diode in the secondary + Elko replace power supply to be safe
Devices: TV
Brand: Panasonic
Model: 2088 gold tc sound
Symptom: No sound crt not live, the heater does not turn on TEG. only 2 volts. b + normal output voltage of the flyback down or not normal.
Cause: flyback damaged.
Solution: replace the flyback
Devices: TV
Brand: Panasonic
Model: 29 inch
Symptoms: while in the program can not be broadcast one else
Cause: The tuner is damaged.
Solution: replace one block full tuner.
Devices: TV
Brand: Panasonic
Model: tc25v20j
Symptoms: The first time a normal lit, a few moments later die out horizontally, while the fixed panel fungi work (volume and channel)
Cause: For 5v voltage processor ic down, is caused by damage to elco (c826) , on the reg filter out 7805.
Solution: elco replaced
Devices: TV
Brand: Panasonic
Model: TC-20S11J
Symptoms: only standby button on the TV does not work in spite of the remote remains in standby
Cause: AC220 unstable voltage
Solution: replace the horizontal DRIVER TR D1275A or C1573
Note: Check all the voltage of the regulator must be stable , if oper. tr always dead
Devices: TV
Brand: Panasonic
Model: TC20T8
Symptoms: TOTAL OFF
Cause: REGULATOR NOT WORK
Solution: CHANGE AND Q804 Q801 C4804 / A1215
Devices: TV
Brand: Panasonic
Model: t20m88
Symptoms: plain raster, blawur, OSD nothing but inarticulate, ill fokus.suara there.
Causes: Abnormal focus voltage
Solution: kmbali trimpot sets the focus FBT, loose and check CRT socket, measure the resistance gnd pin CRT thd other pin, position x10k ohm meter, if the needle moves sdikit course, you should replace the socket.
Devices: TV
Brand: Panasonic
Model: 21 Inch
Symptoms: The first turned on Image Blur (morbidly Focus) .After +/- 5 minutes, the picture gradually to normal
Cause: Socket tube corrosion (Gross)
Solution: Replace the Tube Socket
Devices: TV
Brand: Panasonic
Model: mc691wj
Symptoms: dim and bright images alternately
Cause: rgb ground problematic
Solution: re-solder ground wires
Devices: TV
Brand: Panasonic
Model: TC14V11
Symptoms: B + high so 110V, 90V normal, working Protek
Cause: R832 (5K6) burning, R837 (1K) broke
Solution: Replace R832 and R837
Devices: TV
Brand: Panasonic
Model: st1465
Symptoms: sounds shrink
Cause: IC 2145 damaged
Solution: replace the IC 2145
Devices: TV
Brand: Panasonic
Model: tc2076rs
Symptoms: total dead, there is a hissing sound, flyback leak
Cause: hit by lightning, flyback leaking and damaged
Solution: replace the flyback
Devices: TV
Brand: Panasonic
Model: gold alfa series
Symptoms: total dead, LED indicators die
Cause: damage to the power supply
Solution: check elco2, 7805 at the regulator ic
Devices: TV
Brand: Panasonic
Model: TC 14S10J
Symptoms: white screen and white blangking lines
Cause: The resistor R 374 1ohm / 2watt breaking result of IC TDA 6107JF short
Solution: replace the R 374 and ic 6107JF to the new TDA
Devices: TV
Brand: Panasonic
Model: tc 2088
Symptom: hoarse voice
Cause: 2301 diode short
Solution: replace the D2301
Devices: TV
Brand: Panasonic
Model: TC-20S11J
Symptoms: only standby button on the TV does not work in spite of the remote remains in standby
Cause: AC220 unstable voltage
Solution: replace the horizontal DRIVER TR D1275A or C1573
Note: Check all the voltage of the regulator must be stable , if oper. tr always dead
Devices: TV
Brand: Panasonic
Model: ts14s100
Symptoms: sound-Klek Klek
Cause: pair r470k drop
Solution: TEG b 90 drop low hihg- find r 470knya in the locker wrote ,, check elco 47 / 50v others
Note: the usual tv mdel gini often occurs
Devices: TV
Brand: Panasonic
Model: 21 top dome
Symptoms: picture looks dim.
Cause: r damaged
Solution: replace the 525 resistor with a value of 137k ohms, namely resistor on abl from B +.
Devices: TV
Brand: Panasonic
Model: TC-21GX20J
Symptoms: total dead
Cause: transient voltage
Solution: replace the horizontal transistor
Devices: TV
Brand: Panasonic
Model: 21 inch
Symptoms: total dead
Cause: eeprom ic damage
Solution: replace the eeprom ic
Devices: TV
Brand: Panasonic
Model: tc-20s11j
Symptoms: Tv can not be on and only the sound of ceklak-ceklik.
Cause: Diodes submitters to elco 100/160 volt in a state short.
Solution: Replace the diode with a diode 3 Amper, select diode having a breakdown voltage above 600 volts.
Note: The short Diodes cause can not being filled elco 100/160-volt, so the TV can not be on.
Devices: TV
Brand: Panasonic
Model: NICAM STEREO
Symptoms: turn on the TV in about 1-2 minutes to die alone, the indicator light also died.
Cause: Elko 100v10uf pda pwr suply dried, in view of his physical already bloated.
Solution: I change the elko , TV returns to normal.
Devices: TV
Brand: Panasonic
Model: TC-SERIES GOLDSOUND
Symptoms: DRAWING LINES ONLY IF CONDITIONS LIGHT VERTICAL horizontal / NORMAL.TAPI NORMAL CONDITIONS IF BRIGHT IN Dim.
Cause: R SHORT
Solution: CHANGE R 525: 120K / 470K
Devices: TV
Brand: Panasonic
Model: alpha gold
Symptoms: image often move moved
Cause: The tuner
Solution: Initially I did re-solder the tuner section remains the same tp continue sy try to replace the new-tuner picture alhamdulillah jrengg ok ...
Devices: TV
Brand: Panasonic
Model: tc 2088
Symptom: There is no image noise, after baeberapa hours on the picture will appear
Cause: Occurs protectionism on rangakaian video, which caused damage to the protectionism in the vertical block
Solution: Try changing the vertical IC, if still Protek Change elco the base of transistor proteknya 100 / 50V that if Karing it will always protectionism in the video sequence.
Note: the terms voltage at the output of the regulator under normal circumstances.
Devices: TV
Brand: Panasonic
Model: TC 2110BC
Symptoms: black picture, normal sound
Cause: elco 220u / 160v dry / leaky
Solution: replace elco 220u / 160v
Devices: TV
Brand: Panasonic
Model: forgot boss
Symptoms: total dead, voice berdenyit2
Cause: short zener56v
Solution: replace the zener and the issue is resolved
Note: liver chasise nyetrum
Devices: TV
Brand: Panasonic
Model: TC.21RY21J
Symptoms: 1.sinyal weak picture is similar symptoms agc.2.gambar damage rather narrow top and bottom
Cause: ic 851 5v output decreases TEG
Solution: replace R889 3.3ohm
Devices: TV
Brand: Panasonic
Model: Goldseris
Symptoms: Tv tidakbisa start voltage had risen high
Cause: Elko 47uf / 50v the series SMPS dry replace both ways
Solution: Check the voltage B + and zener second check Elko 47uf / 50v on the primary SMPS also check elko the secondary part SMPS
Note: Check the circuit bost up
Devices: TV
Brand: Panasonic
Model: TC21FJ50J
Symptoms: Arise Horizontal lines
Cause: Cracks on the vertical IC
Solution: re-solder the vertical section and replace capacitor bag. vertical
Devices: TV
Brand: Panasonic
Model: tc-2012Rc
Symptoms: can not keep a program canel.
Cause: one diode OA90ag there are broken / short.
Solution: check of diode 5 is one of some end / short.tipe is difficult in toko.ganti can just use the former old school radio, but I try to replace the use in 4148 could be.
Devices: TV
Brand: Panasonic
Model: mx series
Symptoms: Protec, must press the power button over and over new start
Cause: Elko 10 / 35v rather short
Solution: replace elco 10 / 35v ato 100 / 35v
Devices: TV
Brand: Panasonic
Model: tc2088
Symptoms: Contrast can not be set
Cause: ABL 220k resistor weak / change resistance
Solution: replace the R 220K ABL
0 Response to "Damage Tv panasonic PROBLEM"
Post a Comment